interfisch
9c84e97a58
add field weakening for command values >1000
2019-11-17 19:33:14 +01:00
interfisch
a2b6f50582
change steer and speed to speedl, speedr
2019-06-14 01:04:39 +02:00
interfisch
1e9a03bc50
copy own changes from old version
2019-06-12 11:39:10 +02:00
3e2cfe973a
Fixed timeout. Now it is usable for other input methods than nunchuck.
...
Cosmetical cleanup in motor-test.
2019-06-01 16:17:48 +02:00
ffda2219f1
Added Motor-Test-Mode: Sweep motors slowly forward and backward without any input.
...
Better config-validation.
Fixed board temperature calculation and serial output when speed > 50.
2019-05-31 19:06:47 +02:00
de94812483
debug serial can use USART2 and USART3
2018-09-03 23:56:08 +02:00
0243eb347e
added board temperature calibration, warning and poweroff (rene-dev and me); rearranged config.h; fixed backwards beep overflow; removed duplicate battery-adc-code (rene-dev); improved battery voltage measurement precision; put poweroff procedure to a separate function; poweroff button now only work if field weakening is 0 (otherwise everything will explode)
2018-07-29 17:30:49 +02:00
612dce68ea
fixed serial debug output, backward beep and low bat beeps work now together, low bat beeps can now be disabled, added inactivity timeout
2018-07-25 12:54:13 +02:00
2932480274
improved low bat detection on other then 10s
2018-07-22 20:34:04 +02:00
a31ea1dcd1
fixed and improved serial debug output
2018-07-22 20:25:40 +02:00
3d0ed7e9c0
now you set battery alert levels in volt per cell and set number of cells. less annoying battery alert beeps. small cleanup.
2018-07-21 17:37:02 +02:00
dd5a128199
added battery voltage calibration, see config.h
2018-07-21 13:56:23 +02:00
38cb5992f2
added more setScopeChannel for debug output, fixed line ending in debug output
2018-07-21 12:09:31 +02:00
1d4dd42bde
RM: unused uart struct
2018-06-11 23:12:10 +02:00
2d2a9c4d11
UPD: usart control now with steer and speed as control values. Btw this is not tested yet but I don't see why it shouldn't work ;)
2018-06-11 14:48:58 +02:00
b3fe48a832
ADD: control via uart. Send two int16 (4 bytes) to usart 2 to control the motors with an arduino or a raspberry pi
2018-06-11 14:29:39 +02:00
88b26123c2
added lots of comments; added some validation to config.h; improved adc-input: added min and max adc-values, added poti calibration, added adc-values to debug-output; added support for a second button connected to adc2; added INVERT_R_DIRECTION and INVERT_L_DIRECTION; updated readme
2018-05-27 22:16:52 +02:00
2dd9d37bb3
Enhance robustness of PPM parsing
...
Add additional checks to ensure only valid PPM pulse trains are accepted.
Add auto-idle feature to ensure vehicle stops if PPM signal is lost.
Co-authored-by: Tobias Mädel <t.maedel@alfeld.de>
2018-05-19 19:24:24 +02:00
ca525abe96
ADD: re-initialize I2C after comms error
2018-05-11 22:04:12 +02:00
8be7681ebf
FIX: ppm interrupt problem
2018-05-11 21:27:21 +02:00
206f67631a
ADD: example code for turbo boost
2018-05-08 13:06:10 +02:00
312d08b944
FIX: license information
2018-05-08 13:02:20 +02:00
aff32b2bb4
ADD: comments from TomTinkering
2018-05-08 12:51:01 +02:00
47f243b2fe
ADD: support for chinese nunchuck
2018-05-06 20:13:11 +02:00
7337a8ae7e
ADD: support for chinese nunchuck
2018-05-06 20:11:53 +02:00
0172976057
ADD: make unlock and make flash to Makefile
2018-04-25 19:27:15 +02:00
5a3ed507b2
ADD: UVLO in config
2018-04-09 22:03:19 +02:00
de8957536c
UPD: more universal codebase for different vehicles
2018-04-09 21:43:59 +02:00
69a14c52a9
ADD: Moving average for Nunchuck readings
2018-04-08 00:15:15 +02:00
fd49c006f7
ADD: Wii Nunchuck control
2018-04-08 00:03:35 +02:00
30f8d97694
ADD: analog commands via ADC
2018-02-26 22:00:09 +01:00
8d31eaf8af
ADD: analog input for vehicle during hackerhotel
2018-02-18 14:02:05 +01:00
ff224a2509
adc in
2018-02-18 13:37:50 +01:00
b988e09e3e
ADD: abs for current measure
2018-02-17 00:19:10 +01:00
6842f7b7fe
ADD: buzzer, undervoltage lockout, safe poweroff, foo
2018-02-10 01:37:36 +01:00
10da0983c6
modified the scope function
2018-02-09 10:11:46 +01:00
a86574bcea
ADD: ppm input
2018-02-09 09:39:47 +01:00
94907b91cf
refactored code, moved user-relevant defines to config.h
2018-02-09 08:53:25 +01:00
86c6106fb7
current feedback "working"
2018-01-07 03:11:55 +01:00
61aff94a26
format
2018-01-06 23:33:34 +01:00
cd5718e151
cleanup
2018-01-06 23:11:22 +01:00
7670cda730
cleanup
2018-01-06 22:59:15 +01:00
cd72ac6ded
dual test
2018-01-06 18:54:51 +01:00
b95d11bd57
foo
2018-01-03 23:55:54 +01:00
73d5c38c88
vel iff0
2017-12-30 04:07:09 +01:00
2556a9bbce
pwm working
2017-12-30 02:55:59 +01:00
interfisch
larsm