fix send mqtt errors only when mqtt enabled

include/helpfunctions.h

@@ -120,4 +120,43 @@ float mapf(float x, float in_min, float in_max, float out_min, float out_max)
 }
 
 
+
+void i2cscan()
+{
+  byte error, address;
+  int nDevices;
+ 
+  delay(500);
+  Serial.println("Scanning...");
+ 
+  nDevices = 0;
+  for(address = 1; address < 127; address++ )
+  {
+    // The i2c_scanner uses the return value of
+    // the Write.endTransmisstion to see if
+    // a device did acknowledge to the address.
+    Wire.beginTransmission(address);
+    error = Wire.endTransmission();
+ 
+    if (error == 0)
+    {
+      Serial.print("I2C device found at address 0x");
+      if (address<16)
+        Serial.print("0");
+      Serial.print(address,HEX);
+      Serial.println("  !");
+ 
+      nDevices++;
+    }
+    else if (error==4)
+    {
+      Serial.print("Unknown error at address 0x");
+      if (address<16)
+        Serial.print("0");
+      Serial.println(address,HEX);
+    }    
+  }
+}
+
+
 #endif 

platformio.ini

@@ -8,7 +8,7 @@
 ; Please visit documentation for the other options and examples
 ; https://docs.platformio.org/page/projectconf.html
 
-[env:esp32doit-devkit-v1_NFT]
+[env:esp32doit-devkit-v1_NFT_2024]
 platform = espressif32
 board = esp32doit-devkit-v1
 framework = arduino
@@ -50,6 +50,7 @@ platform = platformio/espressif32@^6.7
 board = esp32-s3-devkitm-1
 ;Devboard is ESP32-S3-DevKitC-1 (N16R8). board=esp32-s3-devkitm-1 works fine
 framework = arduino
+monitor_port = /dev/ttyACM1
 
 monitor_speed = 115200
 
@@ -86,3 +87,49 @@ lib_deps =
     256dpi/MQTT@^2.5.2
     pololu/VL53L0X@^1.3.1
     adafruit/Adafruit NeoPixel
+
+
+
+
+[env:esp32-s3-devkitm-1_NFT]
+platform = platformio/espressif32@^6.7
+board = esp32-s3-devkitm-1
+;Devboard is ESP32-S3-DevKitC-1 (N16R8). board=esp32-s3-devkitm-1 works fine
+framework = arduino
+
+monitor_speed = 115200
+monitor_port = /dev/ttyACM0
+
+
+
+build_flags=
+    '-D CLIENT_ID="hydroponic-NFT"'
+    -D PIN_BUTTON=12
+
+    -D EC_PIN_RELAY_PROBE=35
+    -D EC_PIN_FREQ=38
+    
+    -D EC_CALIBRATION_POLYNOM={8.718380956513695,-0.026463423062356713,3.425216464107108e-05,-4.069826379094172e-09,2.478900495960682e-13}
+    -D EC_CALIBRATION_LINEARIZE_BELOW_ADC=2000
+    -D EC_CALIBRATION_LINEAR_LOWADC=728
+    -D EC_CALIBRATION_LINEAR_LOWEC=0
+
+    -D FLOW_PIN=17
+    -D ONE_WIRE_BUS_PIN=18
+    -D THERMOMETER_ADDR_RESERVOIR={0x28,0xFF,0x6F,0x19,0x72,0x16,0x05,0x44}
+    -D THERMOMETER_ADDR_CASE={0x28,0xFF,0x64,0x0E,0x75,0x90,0xDE,0x02}
+
+    -D PIN_SDA=1
+    -D PIN_SCL=2
+
+    -D WATERLEVEL_OFFSET=500.0
+    -D WATERLEVEL_FACTOR=-1.0
+    -D RES_AREA=20*20*3.1416
+
+lib_deps =
+    https://github.com/milesburton/Arduino-Temperature-Control-Library/
+    https://github.com/emilv/ArduinoSort/
+    robtillaart/ADS1X15@^0.3.9
+    256dpi/MQTT@^2.5.2
+    pololu/VL53L0X@^1.3.1
+    adafruit/Adafruit NeoPixel

src/main.cpp

@@ -9,57 +9,19 @@ unsigned long last_check=0;
 #include "wifi_functions.h"
 
 bool debug=false; //print Serial information
-bool mqtt=true;
+bool mqtt=false;
-bool eccalibrationoutput=false; //serial output for ec calibration
+bool eccalibrationoutput=true; //serial output for ec calibration
 /* Write to file with:
 sudo stty -F /dev/ttyUSB0 115200
 cat /dev/ttyUSB0 | tee received.txt
+
+falls nicht geht, vorher einmal kurz per screen verbinden
 */
 
 bool valuesStabilized=false; //gets set true when values are stable (avaeraging arrays filled)
 
 
 
- 
-void i2cscan()
-{
-  byte error, address;
-  int nDevices;
- 
-  delay(500);
-  Serial.println("Scanning...");
- 
-  nDevices = 0;
-  for(address = 1; address < 127; address++ )
-  {
-    // The i2c_scanner uses the return value of
-    // the Write.endTransmisstion to see if
-    // a device did acknowledge to the address.
-    Wire.beginTransmission(address);
-    error = Wire.endTransmission();
- 
-    if (error == 0)
-    {
-      Serial.print("I2C device found at address 0x");
-      if (address<16)
-        Serial.print("0");
-      Serial.print(address,HEX);
-      Serial.println("  !");
- 
-      nDevices++;
-    }
-    else if (error==4)
-    {
-      Serial.print("Unknown error at address 0x");
-      if (address<16)
-        Serial.print("0");
-      Serial.println(address,HEX);
-    }    
-  }
-}
-
-
-
 #include "helpfunctions.h"
 #include "ADS1X15.h"
 
@@ -155,7 +117,9 @@ void setup() {
   //init ADS1115
   if (!ADS.begin()) {
     Serial.println("Error:"); delay(2000); Serial.println("ADS1115 Init Error!");
+    if (mqtt){
       publishInfo("error/general","ADS1115 Init Error");
+    }
     adsenabled=false;
   }
   if (adsenabled){
@@ -307,11 +271,12 @@ void loop() {
         pixels.setPixelColor(0, pixels.Color(0,0,0));
         pixels.show();
 #endif
+    Serial.print(CLIENT_ID);  Serial.print(",");
     Serial.print(loopmillis); Serial.print(",");
     Serial.print(tempCmean_reservoir); Serial.print(",");
     Serial.print(ec_calib_adc); Serial.print(",");
     Serial.print(ec_adc); Serial.print(",");
-    Serial.print(ec_adc_adjusted); Serial.print(",");
+    Serial.print(ec_adc_adjusted);
     Serial.println();
   }
   
@@ -326,12 +291,16 @@ void loop() {
       if (!valueError && valuesStabilized) { //error just appeared
         if (tempCmean_reservoir==DEVICE_DISCONNECTED_C) {
           Serial.println("valueError tempCmean_reservoir");
+          if (mqtt){
             publishInfo("error/temperature","valueError tempCmean_reservoir");
           }
+        }
         if (tempCmean_case==DEVICE_DISCONNECTED_C) {
           Serial.println("valueError tempCmean_case");
+          if (mqtt){
             publishInfo("error/temperature","valueError tempCmean_case");
           }
+        }
         
         
       }
@@ -347,9 +316,11 @@ void loop() {
       if (!valueError && valuesStabilized) { //error just appeared
         if (ec==EC_UNAVAILABLE){
           Serial.println("valueError ec");
+          if (mqtt){
             publishInfo("error/ec","valueError ec");
           }
         }
+      }
       valueError=true;
       _noErrorsDuringLoop=false;
     }
@@ -360,8 +331,10 @@ void loop() {
     if (distance_unsuccessful_count>20) {
       if (!valueError && valuesStabilized) { //error just appeared
         Serial.println("valueError distance");
+        if (mqtt){ 
           publishInfo("error/waterlevel","valueError distance");
         }
+      }
       valueError=true;
       _noErrorsDuringLoop=false;
     }