266 lines
7.0 KiB
C++
266 lines
7.0 KiB
C++
//https://github.com/rogerclarkmelbourne/Arduino_STM32 in arduino/hardware
|
|
//Board: Generic STM32F103C series
|
|
//Upload method: serial
|
|
//20k RAM 64k Flash
|
|
|
|
// RX ist A10, TX ist A9 (3v3 level)
|
|
//to flash set boot0 (the one further away from reset button) to 1 and press reset, flash, program executes immediately
|
|
//set boot0 back to 0 to run program on powerup
|
|
|
|
//#define DEBUG
|
|
|
|
#define PIN_LED PC13
|
|
|
|
#define SENDPERIOD 20 //ms
|
|
|
|
#define IMUUPDATEPERIOD 10 //ms
|
|
long last_imuupdated=0;
|
|
|
|
|
|
#include <IMUGY85.h>
|
|
//https://github.com/fookingthg/GY85
|
|
//ITG3200 and ADXL345 from https://github.com/jrowberg/i2cdevlib/tree/master/Arduino
|
|
//https://github.com/mechasolution/Mecha_QMC5883L //because QMC5883 on GY85 instead of HMC5883, source: https://circuitdigest.com/microcontroller-projects/digital-compass-with-arduino-and-hmc5883l-magnetometer
|
|
//in qmc5883L library read values changed from uint16_t to int16_t
|
|
|
|
IMUGY85 imu;
|
|
double ax, ay, az, gx, gy, gz, roll, pitch, yaw, mx,my,mz,ma;
|
|
double setYaw=0;
|
|
|
|
|
|
//from left to right. pins at bottom. chips on top
|
|
//1 GND (black)
|
|
//2 Data
|
|
//3 Clock
|
|
//4 Reset
|
|
//5 +5V (red)
|
|
//6 Right BTN
|
|
//7 Middle BTN
|
|
//8 Left BTN
|
|
//pinout: https://martin-prochnow.de/projects/thinkpad_keyboard
|
|
//see also https://github.com/feklee/usb-trackpoint/blob/master/code/code.ino
|
|
|
|
#include <SPI.h>
|
|
#include "nRF24L01.h"
|
|
#include "RF24.h"
|
|
|
|
RF24 radio(PB0,PB1); //ce, cs
|
|
//SCK D13 (Pro mini), A5 (bluepill)
|
|
//Miso D12 (Pro mini), A6 (bluepill)
|
|
//Mosi D11 (Pro mini), A7 (bluepill)
|
|
|
|
// Radio pipe addresses for the 2 nodes to communicate.
|
|
const uint64_t pipes[2] = { 0xF0F0F0F0E1LL, 0xF0F0F0F0D2LL };
|
|
|
|
struct nrfdata {
|
|
uint8_t steer;
|
|
uint8_t speed;
|
|
uint8_t commands; //bit 0 set = motor enable
|
|
uint8_t checksum;
|
|
};
|
|
|
|
nrfdata lastnrfdata;
|
|
long last_nrfreceive=0; //last time values were received and checksum ok
|
|
long nrf_delay=0;
|
|
#define MAX_NRFDELAY 50
|
|
|
|
//command variables
|
|
boolean motorenabled=false; //set by nrfdata.commands
|
|
|
|
|
|
|
|
|
|
long last_send=0;
|
|
|
|
int16_t out_steer=0; //between -1000 and 1000
|
|
int16_t out_speed=0;
|
|
uint8_t out_checksum=0; //0= disable motors, 255=reserved, 1<=checksum<255
|
|
#define NRFDATA_CENTER 127
|
|
|
|
boolean armed=false;
|
|
|
|
|
|
|
|
void setup() {
|
|
|
|
Serial.begin(115200); //Debug and Program. A9=TX1, A10=RX1 (3v3 level)
|
|
|
|
Serial2.begin(19200); //control. B10=TX3, B11=RX3 (Serial2 is Usart 3)
|
|
|
|
|
|
pinMode(PIN_LED, OUTPUT);
|
|
digitalWrite(PIN_LED,HIGH);
|
|
|
|
|
|
Serial.println("Initializing nrf24");
|
|
|
|
radio.begin();
|
|
|
|
|
|
radio.setRetries(15,15); // optionally, increase the delay between retries & # of retries
|
|
radio.setPayloadSize(8); // optionally, reduce the payload size. seems to improve reliability
|
|
|
|
radio.openWritingPipe(pipes[0]); //write on pipe 0
|
|
radio.openReadingPipe(1,pipes[1]); //read on pipe 1
|
|
|
|
radio.startListening();
|
|
|
|
Serial.println("Initializing IMU");
|
|
imu.init();
|
|
|
|
Serial.println("Initialized");
|
|
|
|
|
|
}
|
|
|
|
void loop() {
|
|
|
|
if (millis()-last_imuupdated>IMUUPDATEPERIOD){
|
|
updateIMU();
|
|
last_imuupdated=millis();
|
|
}
|
|
|
|
//NRF24
|
|
nrf_delay=millis()-last_nrfreceive; //update nrf delay
|
|
if ( radio.available() )
|
|
{
|
|
//Serial.println("radio available ...");
|
|
bool done = false;
|
|
while (!done)
|
|
{
|
|
digitalWrite(PIN_LED, !digitalRead(PIN_LED));
|
|
done = radio.read( &lastnrfdata, sizeof(nrfdata) );
|
|
|
|
//parse commands
|
|
motorenabled = (lastnrfdata.commands & (1 << 0)); //check bit 0
|
|
if (!motorenabled){ //disable motors?
|
|
armed=false;
|
|
}
|
|
|
|
if (lastnrfdata.speed==NRFDATA_CENTER && lastnrfdata.speed==NRFDATA_CENTER){ //arm only when centered
|
|
armed=true; //arm at first received packet
|
|
}
|
|
|
|
uint8_t calcchecksum=(uint8_t)((lastnrfdata.steer+3)*(lastnrfdata.speed+13));
|
|
if (lastnrfdata.checksum!=calcchecksum){ //checksum not ok?
|
|
armed=false;
|
|
}else{ //checksum ok
|
|
last_nrfreceive=millis();
|
|
}
|
|
|
|
#ifdef DEBUG
|
|
Serial.print("Received:");
|
|
Serial.print(" st=");
|
|
Serial.print(lastnrfdata.steer);
|
|
Serial.print(", sp=");
|
|
Serial.print(lastnrfdata.speed);
|
|
Serial.print(", c=");
|
|
Serial.print(lastnrfdata.commands);
|
|
Serial.print(", chks=");
|
|
Serial.print(lastnrfdata.checksum);
|
|
|
|
Serial.print("nrfdelay=");
|
|
Serial.print(nrf_delay);
|
|
#endif
|
|
|
|
//y positive = forward
|
|
//x positive = right
|
|
|
|
setYaw+=((int16_t)(lastnrfdata.steer)-NRFDATA_CENTER)*10/127;
|
|
while (setYaw<0){
|
|
setYaw+=360;
|
|
}
|
|
while (setYaw>=360){
|
|
setYaw-=360;
|
|
}
|
|
|
|
/*
|
|
Serial.print("setYaw=");
|
|
Serial.print(setYaw);
|
|
Serial.print(" Yaw=");
|
|
Serial.println(yaw);*/
|
|
|
|
}
|
|
}
|
|
|
|
if (armed && nrf_delay>=MAX_NRFDELAY){ //too long since last sucessful nrf receive
|
|
armed=false;
|
|
}
|
|
if (armed){
|
|
//out_speed=(int16_t)( (lastnrfdata.y-TRACKPOINT_CENTER)*1000/TRACKPOINT_MAX );
|
|
//out_steer=(int16_t)( -(lastnrfdata.x-TRACKPOINT_CENTER)*1000/TRACKPOINT_MAX );
|
|
out_speed=(int16_t)( ((int16_t)(lastnrfdata.speed)-NRFDATA_CENTER)*1000/127 ); //-1000 to 1000
|
|
//out_steer=(int16_t)( ((int16_t)(lastnrfdata.steer)-NRFDATA_CENTER)*1000/127 );
|
|
//Test Mag
|
|
double yawdiff=(setYaw-180)-(yaw-180); //following angle difference works only for angles [-180,180]. yaw here is [0,360]
|
|
yawdiff += (yawdiff>180) ? -360 : (yawdiff<-180) ? 360 : 0;
|
|
//yawdiff/=2;
|
|
int yawdiffsign=1;
|
|
if (yawdiff<0){
|
|
yawdiffsign=-1;
|
|
}
|
|
yawdiff=yawdiff*yawdiff; //square
|
|
yawdiff=constrain(yawdiff/2,0,800);
|
|
yawdiff*=yawdiffsign; //redo sign
|
|
|
|
out_steer=(int16_t)( yawdiff );
|
|
/*
|
|
Serial.print("Out steer=");
|
|
Serial.println(out_steer);*/
|
|
|
|
}else{ //took too long since last nrf data
|
|
out_steer=0;
|
|
out_speed=0;
|
|
}
|
|
|
|
|
|
|
|
|
|
if (millis()-last_send>SENDPERIOD){
|
|
//calculate checksum
|
|
out_checksum = ((uint8_t) ((uint8_t)out_steer)*((uint8_t)out_speed)); //simple checksum
|
|
if (out_checksum==0 || out_checksum==255){ out_checksum=1; } //cannot be 0 or 255 (special purpose)
|
|
|
|
if (!motorenabled){ //disable motors?
|
|
out_checksum=0; //checksum=0 disables motors
|
|
}
|
|
|
|
Serial2.write((uint8_t *) &out_steer, sizeof(out_steer));
|
|
Serial2.write((uint8_t *) &out_speed, sizeof(out_speed));
|
|
Serial2.write((uint8_t *) &out_checksum, sizeof(out_checksum));
|
|
last_send=millis();
|
|
|
|
|
|
#ifdef DEBUG
|
|
Serial.print(" steer=");
|
|
Serial.print(out_steer);
|
|
Serial.print(" speed=");
|
|
Serial.print(out_speed);
|
|
Serial.print(" checksum=");
|
|
Serial.print(out_checksum);
|
|
|
|
Serial.println();
|
|
#endif
|
|
}
|
|
|
|
}
|
|
|
|
|
|
void updateIMU()
|
|
{
|
|
//Update Imu and write to variables
|
|
imu.update();
|
|
imu.getAcceleration(&ax, &ay, &az);
|
|
imu.getGyro(&gx, &gy, &gz);
|
|
imu.getMag(&mx, &my, &mz,&ma); //calibration data such as bias is set in IMUGY85.h
|
|
roll = imu.getRoll();
|
|
pitch = imu.getPitch();
|
|
yaw = imu.getYaw();
|
|
/*Directions:
|
|
* Components on top.
|
|
* Roll: around Y axis (pointing to the right), left negative
|
|
* Pitch: around X axis (pointing forward), up positive
|
|
* Yaw: around Z axis, CCW positive, 0 to 360
|
|
*/
|
|
}
|