138 lines
7.2 KiB
C
138 lines
7.2 KiB
C
#pragma once
|
|
#include "stm32f1xx_hal.h"
|
|
|
|
// ################################################################################
|
|
|
|
#define PWM_FREQ 16000 // PWM frequency in Hz
|
|
#define DEAD_TIME 32 // PWM deadtime
|
|
|
|
#define DC_CUR_LIMIT 15 // DC current limit in amps per motor. so 15 means it will draw 30A out of your battery. it does not disable motors, it is a soft current limit.
|
|
|
|
#define DELAY_IN_MAIN_LOOP 5 // in ms. default 5. it is independent of all the timing critical stuff. do not touch if you do not know what you are doing.
|
|
|
|
// Battery voltage calibration: connect power source. use multimeter to measure real voltage and write it to BAT_CALIB_REAL_VOLTAGE. enable DEBUG_SERIAL_USART3 and DEBUG_SERIAL_ASCII (and disconnect and disable CONTROL_NUNCHUCK) and watch UART on right sensor board cable. write value nr 5 to BAT_CALIB_ADC. make and flash firmware. you can verify voltage on UART debug value 6 (devide it by 100.0 to get calibrated voltage).
|
|
#define BAT_CALIB_REAL_VOLTAGE 42.0 // input voltage measured by multimeter
|
|
#define BAT_CALIB_ADC 1667 // adc-value measured by mainboard (value nr 4 on UART debug output)
|
|
|
|
#define BAT_NUMBER_OF_CELLS 12 // normal Hoverboard battery: 10s
|
|
#define BAT_LOW_LVL1_ENABLE 0 // to beep or not to beep, 1 or 0
|
|
#define BAT_LOW_LVL1 3.6 // gently beeps at this voltage level. [V/cell]
|
|
#define BAT_LOW_LVL2_ENABLE 1 // to beep or not to beep, 1 or 0
|
|
#define BAT_LOW_LVL2 3.5 // your battery is almost empty. Charge now! [V/cell]
|
|
#define BAT_LOW_DEAD 3.37 // undervoltage lockout. [V/cell]
|
|
|
|
#define INACTIVITY_TIMEOUT 8 // minutes of not driving until poweroff. it is not very precise.
|
|
|
|
// ################################################################################
|
|
|
|
//#define DEBUG_SERIAL_USART3 // right sensor board cable, disable if I2C (nunchuck) is used!
|
|
#define DEBUG_BAUD 115200 // UART baud rate
|
|
//#define DEBUG_SERIAL_SERVOTERM
|
|
#define DEBUG_SERIAL_ASCII // "1:345 2:1337 3:0 4:0 5:0 6:0 7:0 8:0\r\n"
|
|
|
|
//#define CONTROL_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used!
|
|
#define CONTROL_BAUD 19200 // control via usart from eg an Arduino or raspberry
|
|
// for Arduino, use void loop(void){ Serial.write((uint8_t *) &steer, sizeof(steer)); Serial.write((uint8_t *) &speed, sizeof(speed));delay(20); }
|
|
|
|
//#define DEBUG_I2C_LCD // standard 16x2 or larger text-lcd via i2c-converter on right sensor board cable
|
|
|
|
#define TIMEOUT 5 // number of wrong / missing commands before emergency off
|
|
|
|
// ################################################################################
|
|
|
|
// ###### CONTROL VIA RC REMOTE ######
|
|
// left sensor board cable. Channel 1: steering, Channel 2: speed.
|
|
//#define CONTROL_PPM // use PPM-Sum as input. disable DEBUG_SERIAL_USART2!
|
|
//#define PPM_NUM_CHANNELS 6 // total number of PPM channels to receive, even if they are not used.
|
|
|
|
// ###### CONTROL VIA TWO POTENTIOMETERS ######
|
|
// ADC-calibration to cover the full poti-range: connect potis to left sensor board cable (0 to 3.3V) (do NOT use the red 15V wire in the cable!). enable DEBUG_SERIAL_USART3 and DEBUG_SERIAL_ASCII (and disconnect and disable CONTROL_NUNCHUCK) and watch UART on right sensor board cable. value1 == ADC1 and value2 == ADC2. write minimum and maximum poti position-values to ADC?_MIN and ADC?_MAX.
|
|
//#define CONTROL_ADC // use ADC as input. disable DEBUG_SERIAL_USART2!
|
|
//#define ADC1_MIN 0 // min ADC1-value while poti at minimum-position (0 - 4095)
|
|
//#define ADC1_MAX 4095 // max ADC1-value while poti at maximum-position (0 - 4095)
|
|
//#define ADC2_MIN 0 // min ADC2-value while poti at minimum-position (0 - 4095)
|
|
//#define ADC2_MAX 4095 // max ADC2-value while poti at maximum-position (0 - 4095)
|
|
|
|
// ###### CONTROL VIA NINTENDO NUNCHUCK ######
|
|
// left sensor board cable. keep cable short, use shielded cable, use ferrits, stabalize voltage in nunchuck, use the right one of the 2 types of nunchucks, add i2c pullups.
|
|
//#define CONTROL_NUNCHUCK // use nunchuck as input. disable DEBUG_SERIAL_USART3!
|
|
|
|
// ################################################################################
|
|
|
|
// ###### DRIVING BEHAVIOR ######
|
|
|
|
// inputs:
|
|
// - cmd1 and cmd2: analog normalized input values. -1000 to 1000
|
|
// - button1 and button2: digital input values. 0 or 1
|
|
// - adc_buffer.l_tx2 and adc_buffer.l_rx2: unfiltered ADC values (you do not need them). 0 to 4095
|
|
// outputs:
|
|
// - speedR and speedL: normal driving -1000 to 1000
|
|
// - weakr and weakl: field weakening for extra boost at high speed (speedR > 700 and speedL > 700). 0 to ~400
|
|
|
|
#define FILTER 0.1 // lower value == softer filter. do not use values <0.01, you will get float precision issues.
|
|
#define SPEED_COEFFICIENT 0.5 // higher value == stronger. 0.0 to ~2.0?
|
|
#define STEER_COEFFICIENT 0.5 // higher value == stronger. if you do not want any steering, set it to 0.0; 0.0 to 1.0
|
|
//#define INVERT_R_DIRECTION
|
|
//#define INVERT_L_DIRECTION
|
|
|
|
//Turbo boost at high speeds while button1 is pressed:
|
|
//#define ADDITIONAL_CODE \
|
|
if (button1 && speedR > 700) { /* field weakening at high speeds */ \
|
|
weakl = cmd1 - 700; /* weak should never exceed 400 or 450 MAX!! */ \
|
|
weakr = cmd1 - 700; } \
|
|
else { \
|
|
weakl = 0; \
|
|
weakr = 0; }
|
|
|
|
// ###### BOBBYCAR ######
|
|
// #define FILTER 0.1
|
|
// #define SPEED_COEFFICIENT -1
|
|
// #define STEER_COEFFICIENT 0
|
|
|
|
// #define ADDITIONAL_CODE \
|
|
if (button1 && speedR < 300) { /* drive backwards */ \
|
|
speedR = speedR * -0.2f; \
|
|
speedL = speedL * -0.2f; } \
|
|
else { \
|
|
direction = 1; } \
|
|
if (button1 && speedR > 700) { /* field weakening at high speeds */ \
|
|
weakl = speedR - 600; /* weak should never exceed 400 or 450 MAX!! */ \
|
|
weakr = speedR - 600; } \
|
|
else { \
|
|
weakl = 0; \
|
|
weakr = 0; }
|
|
|
|
// ###### ARMCHAIR ######
|
|
// #define FILTER 0.05
|
|
// #define SPEED_COEFFICIENT 0.5
|
|
// #define STEER_COEFFICIENT -0.2
|
|
|
|
// #define ADDITIONAL_CODE if (button1 && scale > 0.8) { /* field weakening at high speeds */ \
|
|
weakl = speedL - 600; /* weak should never exceed 400 or 450 MAX!! */ \
|
|
weakr = speedR - 600; } \
|
|
else {\
|
|
weakl = 0;\
|
|
weakr = 0;
|
|
|
|
#define BEEPS_BACKWARD 1 // 0 or 1
|
|
|
|
// ################################################################################
|
|
|
|
// validate settings (do not touch this):
|
|
|
|
#if defined DEBUG_SERIAL_USART2 && defined CONTROL_ADC
|
|
#error CONTROL_ADC and DEBUG_SERIAL_USART2 not allowed. use DEBUG_SERIAL_USART3 instead.
|
|
#endif
|
|
|
|
#if defined DEBUG_SERIAL_USART2 && defined CONTROL_PPM
|
|
#error CONTROL_PPM and DEBUG_SERIAL_USART2 not allowed. use DEBUG_SERIAL_USART3 instead.
|
|
#endif
|
|
|
|
#if defined DEBUG_SERIAL_USART3 && defined CONTROL_NUNCHUCK
|
|
#error CONTROL_NUNCHUCK and DEBUG_SERIAL_USART3 not allowed. use DEBUG_SERIAL_USART2 instead.
|
|
#endif
|
|
|
|
#if defined CONTROL_PPM && defined CONTROL_ADC && defined CONTROL_NUNCHUCK || defined CONTROL_PPM && defined CONTROL_ADC || defined CONTROL_ADC && defined CONTROL_NUNCHUCK || defined CONTROL_PPM && defined CONTROL_NUNCHUCK
|
|
#error only 1 input method allowed. use CONTROL_PPM or CONTROL_ADC or CONTROL_NUNCHUCK.
|
|
#endif
|