interfisch
/
hoverboard-firmware-hack-foc-serial-esc
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
hoverboard-firmware-hack-fo.../01_Matlab/99_RecycleBin/init_model_Ffwd.m

245 lines
11 KiB
Mathematica
Raw Permalink Normal View History

Initial commit
2019-10-06 13:09:15 +00:00
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% This file is part of the hoverboard-new-firmware-hack project
% Compared to previouse commutation method, this project implements
% FOC (Field Oriented Control) for BLDC motors with Hall sensors.
% The new control methods offers superior performanace
% compared to previous method featuring:
% >> reduced noise and vibrations
% >> smooth torque output
% >> improved motor efficiency -> lower energy consumption
%
% Author: Emanuel FERU
% Copyright <EFBFBD> 2019 Emanuel FERU <aerdronix@gmail.com>
%
% This program is free software: you can redistribute it and/or modify
% it under the terms of the GNU General Public License as published by
% the Free Software Foundation, either version 3 of the License, or
% (at your option) any later version.
%
% This program is distributed in the hope that it will be useful,
% but WITHOUT ANY WARRANTY; without even the implied warranty of
% MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
% GNU General Public License for more details.
%
% You should have received a copy of the GNU General Public License
% along with this program. If not, see <http://www.gnu.org/licenses/>.
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% Clear workspace
close all
clear
clc
% Load model parameters
load BLDCmotorControl_data;
Ts = 5e-6; % [s] Model sampling time (200 kHz)
Ts_ctrl = 6e-5; % [s] Controller sampling time (~16 kHz)
f_ctrl = 16e3; % [Hz] Controller frequency = 1/Ts_ctrl (16 kHz)
% Ts_ctrl = 12e-5; % [s] Controller sampling time (~8 kHz)
% Motor parameters
n_polePairs = 15; % [-] Number of pole pairs
a_elecPeriod = 360; % [deg] Electrical angle period
a_elecAngle = 60; % [deg] Electrical angle between two Hall sensor changing events
a_mechAngle = a_elecAngle / n_polePairs; % [deg] Mechanical angle
r_whl = 6.5 * 2.54 * 1e-2 / 2; % [m] Wheel radius. Diameter = 6.5 inch (1 inch = 2.54 cm): Speed[kph] = rpm*(pi/30)*r_whl*3.6
i_sca = 50; % [-] [not tunable] Scalling factor A to int16 (50 = 1/0.02)
%% Control Manager
% Control type selection
CTRL_COM = 0; % [-] Commutation Control
CTRL_FOC = 1; % [-] Field Oriented Control (FOC)
z_ctrlTypSel = 1; % [-] Control Type Selection
% Control model request
OPEN_MODE = 0; % [-] Open mode
VLT_MODE = 1; % [-] Voltage mode
SPD_MODE = 2; % [-] Speed mode
TRQ_MODE = 3; % [-] Torque mode
z_ctrlModReq = 1; % [-] Control Mode Request
%% F01_Estimations
% Position Estimation Parameters
% Hall = 4*hA + 2*hB + hC
% Hall = [0 1 2 3 4 5 6 7]
vec_hallToPos = [0 2 0 1 4 3 5 0]; % [-] Mapping Hall signal to position
% Speed Calculation Parameters
cf_speedCoef = round(f_ctrl * a_mechAngle * (pi/180) * (30/pi)); % [-] Speed calculation coefficient (factors are due to conversions rpm <-> rad/s)
z_maxCntRst = 2000; % [-] Maximum counter value for reset (works also as time-out to detect standing still)
n_commDeacvHi = 30; % [rpm] Commutation method deactivation speed high
n_commAcvLo = 15; % [rpm] Commutation method activation speed low
dz_cntTrnsDetHi = 40; % [-] Counter gradient High for transient behavior detection (used for speed estimation)
dz_cntTrnsDetLo = 20; % [-] Counter gradient Low for steady state detection (used for speed estimation)
n_stdStillDet = 3; % [rpm] Speed threshold for Stand still detection
cf_currFilt = 0.02; % [%] Current filter coefficient [0, 1]. Lower values mean softer filter
cf_speedFilt = 0.20; % [%] Speed filter coefficient [0, 1]. Lower values mean softer filter
%% F02_Diagnostics
b_diagEna = 1; % [-] Diagnostics enable flag: 0 = Disabled, 1 = Enabled
t_errQual = 0.8 * f_ctrl; % [s] Error qualification time
t_errDequal = 2 * f_ctrl; % [s] Error dequalification time
i_errThres = 40 * i_sca; % [A] Maximum current threshold for phase current error detection
%% F04_Field_Oriented_Control
b_FfwdEna = 1; % [-] Feedforward enable flag: 0 = Disabled, 1 = Enabled
mot_Lq = 0; % [uH] Motor Q axis inductance
mot_Ld = 0; % [uH] Motor D axis inductance
mot_lambda = 0; % [mWb] Motor flux linkage
b_selPhaABCurrMeas = 1; % [-] Measured phase currents selection: {iA,iB} = 1; {iB,iC} = 0
i_thresOutlier = 200; % [-] Threshold for outlier detection in the current measurement
b_DCLinkCurrAvail = 0; % [-] Flag for DC Link current measurement availability
dV_openRate = 1000 * Ts_ctrl; % [V/s] Rate for voltage cut-off in Open Mode (Sample Time included in the rate)
% Field Weakening
b_fieldWeakEna = 0; % [-] Field weakening enable parameter: 0 = disable (default), 1 = enable
% id_fieldWeak_M1 = [ 0 0 0.25 0.5 1 2 3 4 4.5 4.8 5 5] * i_sca; % [-] Field weakening current map
% n_fieldWeak_XA = [200 250 300 350 400 450 500 550 600 650 700 750]; % [rpm] Motor speed grid
id_fieldWeak_M1 = [ 0 0 0.05 0.25 1 2 3 4 4.5 4.8 5 5] * i_sca; % [-] Field weakening current map
n_fieldWeak_XA = [400 420 440 460 480 500 520 540 560 580 600 620]; % [rpm] Motor speed grid
% figure
% plot(n_fieldWeak_XA, id_fieldWeak_M1, '.-'); hold on
% grid
% Sine wave look-up table
res_elecAngle = 2;
a_elecAngle_XA = 0:res_elecAngle:360; % [deg] Electrical angle grid
r_sin_M1 = sin((a_elecAngle_XA + 30)*(pi/180)); % Note: 30 deg shift is to allign it with the Hall sensors position
r_cos_M1 = cos((a_elecAngle_XA + 30)*(pi/180));
% figure
% stairs(a_elecAngle_XA, r_sin_M1); hold on
% stairs(a_elecAngle_XA, r_cos_M1);
% legend('sin','cos');
% Voltage Limitations
V_margin = 100; % [-] Voltage margin to make sure that there is a sufficiently wide pulse for a good phase current measurement
Vd_max = 1000 - V_margin;
Vq_max_XA = 0:20:Vd_max;
Vq_max_M1 = sqrt(Vd_max^2 - Vq_max_XA.^2); % Circle limitations look-up table
% figure
% stairs(Vq_max_XA, Vq_max_M1); legend('V_{max}');
% Current Limitations
iq_KpLimProt = 4; % [-] Current limit protection gain
iq_KiLimProt = 3 * Ts_ctrl; % [-] Current limit protection integral gain (only used in SPEED_MODE)
i_max = 15; % [A] Maximum allowed motor current (continuous)
i_max = i_max * i_sca;
iq_max_XA = 0:15:i_max;
iq_max_M1 = sqrt(i_max^2 - iq_max_XA.^2); % Circle limitations look-up table
% figure
% stairs(iq_max_XA, iq_max_M1); legend('i_{max}');
% Speed limitations
n_KpLimProt = 5; % [-] Speed limit protection gain
n_max = 800; % [rpm] Maximum motor speed
% PI control gains
n_Kp = 1;%5;
n_Ki = 10 * Ts_ctrl;%50 * Ts_ctrl; % Ts_ctrl embedded in Ki to avoid one multipilication in the controller
n_Kb = 1000 * Ts_ctrl;
iq_Kp = 0.5;
iq_Ki = 100 * Ts_ctrl;
iq_Kb = 1000 * Ts_ctrl;
id_Kp = 0.5;
id_Ki = 80 * Ts_ctrl;
id_Kb = 1000 * Ts_ctrl;
%% F05_Control_Type_Management
% Commutation method
z_commutMap_M1 = [-1 -1 0 1 1 0; % Phase A
1 0 -1 -1 0 1; % Phase B
0 1 1 0 -1 -1]; % Phase C [-] Commutation method map
% ***********************************************************************************
disp('---- BLDC_controller: Initialization OK ----');
%% Plot control methods
show_fig = 0;
sca_factor = 1000; % [-] scalling factor (to avoid truncation approximations on integer data type)
% Trapezoidal method
a_trapElecAngle_XA = [0 60 120 180 240 300 360]; % [deg] Electrical angle grid
r_trapPhaA_M1 = sca_factor*[ 1 1 1 -1 -1 -1 1];
r_trapPhaB_M1 = sca_factor*[-1 -1 1 1 1 -1 -1];
r_trapPhaC_M1 = sca_factor*[ 1 -1 -1 -1 1 1 1];
% Sinusoidal method
a_sinElecAngle_XA = 0:10:360;
omega = a_sinElecAngle_XA*(pi/180);
pha_adv = 30; % [deg] Phase advance to mach commands with the Hall position
r_sinPhaA_M1 = -sca_factor*sin(omega + pha_adv*(pi/180));
r_sinPhaB_M1 = -sca_factor*sin(omega - 120*(pi/180) + pha_adv*(pi/180));
r_sinPhaC_M1 = -sca_factor*sin(omega + 120*(pi/180) + pha_adv*(pi/180));
% SVM (Space Vector Modulation) calculation
SVM_vec = [r_sinPhaA_M1; r_sinPhaB_M1; r_sinPhaC_M1];
SVM_min = min(SVM_vec);
SVM_max = max(SVM_vec);
SVM_sum = SVM_min + SVM_max;
SVM_vec = SVM_vec - 0.5*SVM_sum;
SVM_vec = (2/sqrt(3))*SVM_vec;
if show_fig
hall_A = [0 0 0 1 1 1 1] + 4;
hall_B = [1 1 0 0 0 1 1] + 2;
hall_C = [0 1 1 1 0 0 0];
color = ['m' 'g' 'b'];
lw = 1.5;
figure
s1 = subplot(221); hold on
stairs(a_trapElecAngle_XA, hall_A, color(1), 'Linewidth', lw);
stairs(a_trapElecAngle_XA, hall_B, color(2), 'Linewidth', lw);
stairs(a_trapElecAngle_XA, hall_C, color(3), 'Linewidth', lw);
xticks(a_trapElecAngle_XA);
grid
yticks(0:5);
yticklabels({'0','1','0','1','0','1'});
title('Hall sensors');
legend('Phase A','Phase B','Phase C','Location','NorthEast');
s2 = subplot(222); hold on
stairs(a_trapElecAngle_XA, hall_A, color(1), 'Linewidth', lw);
stairs(a_trapElecAngle_XA, hall_B, color(2), 'Linewidth', lw);
stairs(a_trapElecAngle_XA, hall_C, color(3), 'Linewidth', lw);
xticks(a_trapElecAngle_XA);
grid
yticks(0:5);
yticklabels({'0','1','0','1','0','1'});
title('Hall sensors');
legend('Phase A','Phase B','Phase C','Location','NorthEast');
s3 = subplot(223); hold on
stairs(a_trapElecAngle_XA, sca_factor*[z_commutMap_M1(1,:) z_commutMap_M1(1,1)] + 6000, color(1), 'Linewidth', lw);
stairs(a_trapElecAngle_XA, sca_factor*[z_commutMap_M1(2,:) z_commutMap_M1(2,1)] + 3000, color(2), 'Linewidth', lw);
stairs(a_trapElecAngle_XA, sca_factor*[z_commutMap_M1(3,:) z_commutMap_M1(3,1)], color(3), 'Linewidth', lw);
xticks(a_trapElecAngle_XA);
yticks(-1000:1000:7000);
yticklabels({'-1000','0','1000','-1000','0','1000','-1000','0','1000'});
ylim([-1000 7000]);
grid
title('Commutation method [0]');
xlabel('Electrical angle [deg]');
s4 = subplot(224); hold on
plot(a_sinElecAngle_XA, SVM_vec(1,:), color(1), 'Linewidth', lw);
plot(a_sinElecAngle_XA, SVM_vec(2,:), color(2), 'Linewidth', lw);
plot(a_sinElecAngle_XA, SVM_vec(3,:), color(3), 'Linewidth', lw);
xticks(a_trapElecAngle_XA);
ylim([-1000 1000])
grid
title('FOC method [1]');
xlabel('Electrical angle [deg]');
linkaxes([s1 s2 s3 s4],'x');
xlim([0 360]);
end