103 lines
3.0 KiB
C
103 lines
3.0 KiB
C
|
#ifndef _TEMPERATURE_H_
|
||
|
|
#define _TEMPERATURE_H_
|
||
|
|
|
||
|
|
#include <OneWire.h>
|
||
|
|
#include <DallasTemperature.h>
|
||
|
|
|
||
|
|
DeviceAddress thermometerESCFront={0x28,0xFF,0x64,0x0E,0x77,0xB0,0xAB,0x4B}; //IC with one marking 28FF640E77B0AB4B
|
||
|
|
float temp_ESCFront;
|
||
|
|
DeviceAddress thermometerESCRear={0x28,0xFF,0x64,0x0E,0x76,0x5D,0x86,0xC2}; //IC with two markings
|
||
|
|
float temp_ESCRear;
|
||
|
|
DeviceAddress thermometerAir={0x28,0xFF,0x64,0x0E,0x74,0x7E,0xFE,0x23}; //IC with three markings 28FF640E747EFE23
|
||
|
|
float temp_Air;
|
||
|
|
|
||
|
|
#define ONE_WIRE_BUS A2 //GPIO pin
|
||
|
|
#define TEMPERATURE_PRECISION 12 //max is 12
|
||
|
|
#define READINTERVAL_DS18B20 5000 //ms
|
||
|
|
|
||
|
|
// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
|
||
|
|
OneWire oneWire(ONE_WIRE_BUS);
|
||
|
|
|
||
|
|
// Pass our oneWire reference to Dallas Temperature.
|
||
|
|
DallasTemperature sensors(&oneWire);
|
||
|
|
|
||
|
|
void initTemperature();
|
||
|
|
void temperatureLoop();
|
||
|
|
void printAddress(DeviceAddress deviceAddress);
|
||
|
|
|
||
|
|
void initTemperature() {
|
||
|
|
|
||
|
|
sensors.begin();
|
||
|
|
delay(1000);
|
||
|
|
|
||
|
|
|
||
|
|
Serial.print("Locating devices...");
|
||
|
|
Serial.print("Found ");
|
||
|
|
Serial.print(sensors.getDeviceCount(), DEC);
|
||
|
|
Serial.println(" devices.");
|
||
|
|
|
||
|
|
delay(1000);
|
||
|
|
|
||
|
|
delay(1000);
|
||
|
|
|
||
|
|
|
||
|
|
//Just search for devices. Only needed when connecting a new sensor to find the address
|
||
|
|
oneWire.reset_search();
|
||
|
|
|
||
|
|
for (uint8_t i=0;i<sensors.getDeviceCount();i++){
|
||
|
|
DeviceAddress _addr;
|
||
|
|
if (!oneWire.search(_addr)) {
|
||
|
|
Serial.print("Error: Device not found");
|
||
|
|
}else{
|
||
|
|
Serial.print("Found device. Address:");
|
||
|
|
printAddress(_addr);
|
||
|
|
}
|
||
|
|
Serial.println();
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
delay(1000);
|
||
|
|
|
||
|
|
//sensors.setResolution(thermometerReservoir, TEMPERATURE_PRECISION);
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
void temperatureLoop(unsigned long loopmillis) {
|
||
|
|
static unsigned long last_read_ds18b20;
|
||
|
|
static bool flag_requestTemperatures=false;
|
||
|
|
if (loopmillis>last_read_ds18b20+READINTERVAL_DS18B20) {
|
||
|
|
if (loopmillis>last_read_ds18b20+READINTERVAL_DS18B20*10) { //timeout
|
||
|
|
Serial.println("Warn: Request Temperatures Timeout!");
|
||
|
|
flag_requestTemperatures=false;
|
||
|
|
}
|
||
|
|
if (!flag_requestTemperatures) {
|
||
|
|
sensors.requestTemperatures(); //this takes ~34ms
|
||
|
|
flag_requestTemperatures=true;
|
||
|
|
}
|
||
|
|
if (sensors.isConversionComplete()) {
|
||
|
|
flag_requestTemperatures=false;
|
||
|
|
last_read_ds18b20=loopmillis;
|
||
|
|
temp_ESCFront= sensors.getTempC(thermometerESCFront); //This takes ~12.5ms
|
||
|
|
temp_ESCRear= sensors.getTempC(thermometerESCRear);
|
||
|
|
temp_Air= sensors.getTempC(thermometerAir);
|
||
|
|
/*
|
||
|
|
Serial.print("temp_ESCFront: "); Serial.println(temp_ESCFront);
|
||
|
|
Serial.print("temp_ESCRear: "); Serial.println(temp_ESCRear);
|
||
|
|
Serial.print("temp_Air: "); Serial.println(temp_Air);
|
||
|
|
*/
|
||
|
|
}
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
void printAddress(DeviceAddress deviceAddress)
|
||
|
|
{
|
||
|
|
for (uint8_t i = 0; i < 8; i++)
|
||
|
|
{
|
||
|
|
// zero pad the address if necessary
|
||
|
|
if (deviceAddress[i] < 16) Serial.print("0");
|
||
|
|
Serial.print(deviceAddress[i], HEX);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
#endif
|