There are many options to configure the functions of FatFs for requirement of each project. The configuration options are defined in the ffconf.h.
Read/Write (0) or Read-only (1). Read-only configuration removes writing API functions, f_write, f_sync, f_unlink, f_mkdir, f_chmod, f_rename, f_truncate, f_getfree and optional writing functions as well.
This option defines minimization level to remove some basic API functions as follows:
| Value | Description |
|---|---|
| 0 | All basic API functions are available. |
| 1 | f_stat, f_getfree, f_unlink, f_mkdir, f_chmod, f_utime, f_truncate and f_rename function are removed. |
| 2 | f_opendir, f_readdir and f_closedir function are removed in addition to 1. |
| 3 | f_lseek function is removed in addition to 2. |
This option switches string functions, f_gets, f_putc, f_puts and f_printf.
| Value | Description |
|---|---|
| 0 | Disable string functions. |
| 1 | Enable string functions without LF-CRLF conversion. |
| 2 | Enable string functions with LF-CRLF conversion. |
Disable (0) or Enable (1) filtered directory read functions, f_findfirst and f_findnext. Also FF_FS_MINIMIZE needs to be 0 or 1.
Disable (0) or Enable (1) f_mkfs function.
Disable (0) or Enable (1) fast seek function to enable accelerated mode for f_lseek, f_read and f_write function. For more information, read here.
Disable (0) or Enable (1) f_expand function.
Disable (0) or Enable (1) metadata control functions, f_chmod and f_utime. Also FF_FS_READONLY needs to be 0.
Disable (0) or Enable (1) API functions for volume label, f_getlabel and f_setlabel.
Disable (0) or Enable (1) f_forward function.
This option specifies the OEM code page to be used on the target system. Incorrect setting of the code page can cause a file open failure. If any non-ASCII character is not used at all, there is no difference between any code pages.
| Value | Code page |
|---|---|
| 0 | Include all code pages below and set by f_setcp() |
| 437 | U.S. |
| 720 | Arabic |
| 737 | Greek |
| 771 | KBL |
| 775 | Baltic |
| 850 | Latin 1 |
| 852 | Latin 2 |
| 855 | Cyrillic |
| 857 | Turkish |
| 860 | Portuguese |
| 861 | Icelandic |
| 862 | Hebrew |
| 863 | Canadian French |
| 864 | Arabic |
| 865 | Nordic |
| 866 | Russian |
| 869 | Greek 2 |
| 932 | Japanese (DBCS) |
| 936 | Simplified Chinese (DBCS) |
| 949 | Korean (DBCS) |
| 950 | Traditional Chinese (DBCS) |
This option switches the support for long file name (LFN). When enable the LFN, Unicode support functions ffunicode.c need to be added to the project. The working buffer for LFN occupies (FF_MAX_LFN + 1) * 2 bytes and additional ((FF_MAX_LFN + 44) / 15 * 32 bytes when exFAT enabled. When use stack for the working buffer, take care on stack overflow. When use heap memory for the working buffer, memory management functions, ff_memalloc and ff_memfree, need to be added to the project.
| Value | Description |
|---|---|
| 0 | Disable LFN. Path name in only 8.3 format can be used. |
| 1 | Enable LFN with static working buffer on the BSS. Always NOT thread-safe. |
| 2 | Enable LFN with dynamic working buffer on the STACK. |
| 3 | Enable LFN with dynamic working buffer on the HEAP. |
This option defines the size of LFN working buffer from 12 to 255 in unit of character. This option has no effect when LFN is disabled.
This option switches character encoding on the API, ANSI/OEM (0) or Unicode in UTF-16 (1). To use Unicode string for the path name, enable LFN and set this option to 1. This option also affects behavior of string I/O functions. When LFN is disabled, this option has no effect. For more information, read here.
When Unicode API is selected by FF_LFN_UNICODE = 1, string I/O functions, f_gets, f_putc, f_puts and f_printf convert the character encodins in it. This option defines the assumption of character encoding on the file to be read/written via those functions. When Unicode API is not selected, the string functions work without any conversion and this option has no effect.
| Value | Description |
|---|---|
| 0 | ANSI/OEM |
| 1 | UTF-16LE |
| 2 | UTF-16BE |
| 3 | UTF-8 |
This option configures relative path function. For more information, read here.
| Value | Description |
|---|---|
| 0 | Disable relative path function and remove related functions. |
| 1 | Enable relative path function. f_chdir and f_chdrive function is available. |
| 2 | f_getcwd function is available in addition to 1 |
This option configures number of volumes (logical drives, from 1 to 10) to be used.
Disable (0) or Enable (1). This option switches the support for string volume ID. When enabled, also pre-defined strings in FF_VOLUME_STRS can be used as drive identifier in the path name.
This option defines the drive ID strings for each logical drives. Number of items must not be less than FF_VOLUMES. Valid characters for the drive ID string are: A-Z and 0-9.
Disable (0) or Enable (1). This option switches multi-partition function. By default (0), each logical drive number is bound to the same physical drive number and only a volume in the physical drive is mounted. When enabled, each logical drive is bound to the partition on the physical drive listed in the user defined partition resolution table VolToPart[]. Also f_fdisk funciton will be available. For more information, read here.
This set of options defines the extent of sector size used on the low level disk I/O interface, disk_read and disk_write function. Valid values are 512, 1024, 2048 and 4096. FF_MIN_SS defines minimum sector size and FF_MAX_SS defines the maximum sector size. Always set both 512 for memory card and harddisk. But a larger value may be required for on-board flash memory and some type of optical media. When FF_MAX_SS > FF_MIN_SS, support of variable sector size is enabled and GET_SECTOR_SIZE command needs to be implemented to the disk_ioctl function.
Disable (0) or Enable (1). This option switches ATA-TRIM function. To enable Trim function, also CTRL_TRIM command should be implemented to the disk_ioctl function.
0 to 3. If you need to know correct free space on the FAT32 volume, set bit 0 of this option, and f_getfree function at first time after volume mount will force a full FAT scan. Bit 1 controls the use of last allocated cluster number.
| Value | Description |
|---|---|
| bit0=0 | Use free cluster count in the FSINFO if available. |
| bit0=1 | Do not trust free cluster count in the FSINFO. |
| bit1=0 | Use last allocated cluster number in the FSINFO to find a free cluster if available. |
| bit1=1 | Do not trust last allocated cluster number in the FSINFO. |
Normal (0) or Tiny (1). At the tiny configuration, size of the file object FIL is reduced FF_MAX_SS bytes. Instead of private data buffer eliminated from the file object, common sector buffer in the filesystem object FATFS is used for the file data transfer.
This option switches support for the exFAT filesystem in addition to the FAT/FAT32 filesystem, Enabled(1) or Disabled(0). To enable this feature, also LFN must be enabled and configureing FF_LFN_UNICODE = 1 and FF_MAX_LFN = 255 is recommended for full-featured exFAT function. Note that enabling exFAT discards ANSI C (C89) compatibility because of need for 64-bit integer type.
Use RTC (0) or Do not use RTC (1). This option controls timestamp function. If the system does not have an RTC function or valid timestamp is not needed, set FF_FS_NORTC to 1 to disable the timestamp function. Any object modified by FatFs will have a fixed timestamp defined by FF_NORTC_MON, FF_NORTC_MDAY and FF_NORTC_YEAR. To use the timestamp function, set FF_FS_NORTC = 0 and add get_fattime function to the project to get the current time form real-time clock. This option has no effect at read-only configuration.
This set of options defines the time to be used at no RTC systems. This option has no effect at read-only configuration or FF_FS_NORTC = 0.
This option switches file lock function to control duplicated file open and illegal operations to open objects. Note that the file lock function is independent of re-entrancy. This option must be 0 at read-only configuration.
| Value | Description |
|---|---|
| 0 | Disable file lock function. To avoid collapsing file by wrong file operation, application program needs to avoid illegal open, remove and rename to the open objects. |
| >0 | Enable file lock function. The value defines how many files/sub-directories can be opened simultaneously under the file lock control. Illigal operations to the open object will be rejected with FR_LOCKED. |
Disable (0) or Enable (1). This option switches the re-entrancy (thread safe) of the FatFs module itself. Note that file/directory access to the different volume is always re-entrant and it can work simultaneously regardless of this option but volume control functions. f_mount, f_mkfs and f_fdisk, are always not re-entrant. Only file/directory access to the same volume, in other words, exclusive use of each filesystem object, is under control of this function. To enable this feature, also user provided synchronization handlers, ff_req_grant, ff_rel_grant, ff_del_syncobj and ff_cre_syncobj, need to be added to the project. Sample code is available in ffsystem.c.
Number of time ticks to abort the file function with FR_TIMEOUT when wait time is too long. This option has no effect when FF_FS_REENTRANT = 0.
This option defines O/S dependent sync object type. e.g. HANDLE, ID, OS_EVENT*, SemaphoreHandle_t and etc. A header file for O/S definitions needs to be included somewhere in the scope of ff.c. This option has no effect when FF_FS_REENTRANT = 0.